Gold from Black Sands

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
I've been re-exploring the black sands rabbit hole recently, and figured I'd share my recent understandings.

I've already visited Larry Blackman's (aka "the essene") path of extracting precious metals from black sand on THIS thread.
Here's the recap:
here’s how I think The Essene was making his gold:
> Perform a lye burn on the black sand from the mine tailings
> Precipitate the ormus white powder metals
> Dissolve the white powder in hydrochloric acid and discard what doesn’t dissolve
> Precipitate the white powder metals back out of hydrochloric acid, then separate out and dry (should be white powder of iridium and gold)
> Mix the dry white powder with sulfur and burn
> Add silver to the white powder and sulfur and melt them all together
> After cooling, place the entire mass in nitric acid to dissolve the silver out (and vapor off remaining sulfur as SO2)
> Remove the remaining solids and put them in aqua regia (this will be gold + iridium metals)
> Remove the remaining solids and melt into a bar (will be iridium metal which doesn’t dissolve in aqua regia)
> Precipitate gold out of the aqua regia, separate it out and melt into a gold bar
> There will probably also be a small amount of platinum dissolved in the remaining solution, which can also precipitate, separate out and melt into a platinum bar.

There's also John Milewski's process of extracting gold from black sand (and glass), which was talked about on THIS post.
Here's the recap:
Just in case these links/videos ever go bad, I'll briefly describe here:
> Wet grind beer bottle glass in hammer mill
> Add magnetite sand and powdered charcoal (or graphite) to the ground glass and water slurry
> Put the mixture into a microwave oven crucible + furnace and fire it up
> Remove from furnace and quench pour the molten slurry into a container of water
> Take the solidified glass mixture and repeat furnace and quench stages to increase yield (John says 10 - 20 times)
> regrind the glass mixture and extract the gold using conventional hydrolic methods (or apparently can also use fire assay technique)
The John Milewski process never specifically described how to get the metallic gold out of the final result, but John said several times in lectures that he used fire assay.
Here's a youtube video showing how to pull gold from black sand using fire assay:

Joe Champion, said in THIS book (which also talked about extracting precious metals from black sand), that you can increase the yields by pre-treating.
He specifically mentioned the following treatment options discovered by other people:
the first common denominator was they directly treated the black sands. And second, each used a high temperature digestion process.

The following is a typical description of their processes:
Don Jordon: NaOH + H202 (sodium hydroxide + hydrogen peroxide). Compound is mixed with the mineral, then fused.

Greg Iseman: 3HC1 + HN03 + HF (Modified Aqua Regia) .
The solution and mineral is placed in an industrial microwave until dissolved.

Beckman Laboratories: Acid Bomb. The mineral is mixed with a flammable chemical constituent, then placed within a high pressure container and ignited by a spark.
Joe also discussed in detail the following treatment option (which was discovered by himself):
For small batches, all that is required is an enclosed laboratory ball mill and black sands. I would recommend Denver Laboratory Ball Mills which are readily available. The black sands used in our tests came from desert deposits outside of Buckeye, Arizona and other sands magnetically separated from rich mineralized copper deposits in New Mexico. The ball mill should be of such design wherein it is completely sealed and has a metallic liner. The balls must be made of non-coat carbon steel. New Teflon coated material will not work. As in the case of the Denver Laboratory mill we used, we had 11.91 kilograms of steel balls with diameters ranging from approximately one-half to 3 inches. We used 2.5 kilograms of black sands. Seal the container and operate for no less than 6-8 hours without interruption. open and take a representative sample of 50.0 grams. Place in sizing screens. If +70% of the material passes through a 200-mesh screen, then remove all the material from the ball mill. However, if the aggregate particle size is greater than 200-mesh, replace the black sands in the mill and operate for an additional 6-8 hours, repeating the same steps. A note of importance. The minimum six hour continuous operation is an extremely important criteria. With operation of three hour intervals, numerous failures have occurred. Wherein operating a continuous +6.0 hours we have yet to see a failure in the production of precious metals....After extensive pulverization(6-8 hours), a significant "nuclear change" occurs within the ball mill. Significant in the fact that by weight 0.5% to 10.0% of the original black sands was converted to precious metals.

The idea of pulling gold out of black sands isn't controversial in and of itself.
Gold prospectors routinely process their black sands to recover hidden particles of gold, such as described HERE.
But the yields significantly vary from different sources.
it depends on gold concentration in the black sand. I had recovered 2.8 grams of gold from 420 grams of black sand from one location. And I got no gold from 340 grams of black sand from different location.

This variance in recovered gold from various sources of black sand reminds me of Vinny Pintos comments [Link HERE]:
All Magnetite Sands Are Not Created Equal
As noted elsewhere on this site, a number of us have found that when using magnetite sand for the purposes of constructing MEOW devices and similar technologies, not all magnetites are created equal, and rather, it seems that there is considerable variance in effectiveness or power across batches and types of magnetite sand.
Even though Vinny was talking about using magnetite for MEOW devices, and Joe was talking about increasing yields from gold extraction from magnetite, for a long time I have wondered if they are not due to the same cause.
In both cases, I've long suspected that repeated cycles of freezing/thawing might be charging the internal HIM portion thereby improving the results.
Unfortunately Vinny never said which areas produce better performing magnetite.
But WRT gold from black sands, it's quite obvious that it's in the colder areas of Australia and New Zealand which regularly dip below freezing where more fine particle gold is found within black sands.
We already know from Reich's work on bion packs that regular freeze and thaw cycles cause various substances to induce healing, and it's assumed that the same process will 'charge' life-force containing water.
I recently assumed that doing freeze/thaw/heat cycles to black sands would further increase the amount of gold recovered in the same way as the other techniques described by Joe Champion.
In fact WRT the Milewski process, that's exactly what I think is happening..Eg: each heat and cool repetition is simply 'charging' the HIM portion of the black sands, so when the final fire assay is performed, it maximises the transmutation power within the black sands.

I had figured that I wanted to test this out by running my own cycles of freeze + heat on black sands, followed by Joe's ball mill process before testing out with a fire assay. I was hoping that this might get very close to Joes' mythical maximum of 10% precious metals from fire assay.
But then we had @Vladimirv join the forums and shared his excellent research about producing ORMUS gas HERE.
In his first ever post to the forums he said:
Before working with ORMUS-containing sources containing large amounts of ORMUS particles, such as azomite, natural Dead Sea salt, sea salt, iron ore magnetite, rock oil mineral, Himalayan pink/black salt, gold or silver ore, it is useful to activate them by exposing them to a pulsating magnetic field, cyclically calcining them at 250-300 degrees Celsius, then boiling them in water and freezing them. Then, grind them for a long time in a ball mill.
I've taken this post and experimental results as a nice little wink from the universe. Thank you @Vladimirv

Anyway, just sharing these musings in case they resonate with anyone else.
 

Lakshmana

Lapidem
Patron of the Arts
Hermetic Pilgrim
Joined
Jan 24, 2022
Messages
1,081
I saw a video on YouTube where someone used a rubber ball mill with quartz glass balls and processed graphite powder ink inside, the graphite/graphene became attracted to magnets after treatment which is not usual.

I think the high energy collision of the balls creates exotic effects when they slam together it can burn a hole trough paper and release a small flash of light.

So yeah, agitation 👍
 
Last edited:

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
I think the high energy collision of the balls creates exotic effects when they slam together it can burn a hole trough paper and release a small flash of light.
I never thought of that before, but you're absolutely right that there's the potential for those conditions to engender some exotic reaction/s.

What I found particularly interesting was Joe's report that running the ball mill for 6 hours without opening it produces more gold than running the ball mill for 2 sets of 3 hours and opening it in-between each set.
I struggled for some time to come up with a model to logically explain that, and here's what I finally came up with....

I imagine the magical HIM particles as residing within the molecular lattice of the magnetite.
But on the very edge of the lattice, they are pulled out by their attraction to oxygen molecule just like a magnet will pull iron filings out of the surface of a sand and iron filing mixture.
When we break the grains of black sand into smaller pieces, the lattices now have new edges with HIM particles exposed to the outside world.
Like this:

him-present.JPG


But after exposure to oxygen, the magical HIM particles all get pulled out of the edges of the lattice leaving it looking like this:
him-gone.JPG


In the case of Joe's 6 hour Ball Mill run, the oxygen inside the container must eventually get saturated with HIM particles and can't pull any more out of the black sands. So all subsequent HIM particles remain on the edge of the lattices, and are then available to work their magic when subjected to the subsequent fire assay.

If true, this would mean that it's crucial to submit the pulverised black sand to fire assay immediately after opening the ball mill and removing it.
[this is because the HIM particles on the edge of the lattice are suddenly exposed to fresh oxygen and will start to get pulled out again if left in open air for too long].

It would also mean that you could further improve Joe's reported results just by displacing all air in the ball mill with a gas like carbon dioxide before you start. [Eg, perhaps you'd get the same results as Joe, but in only half the time since you no longer have to saturate the oxygen inside the ball mill with gassed off HIM particles]

However, what I'm particularly interested in WRT this, is that this might also provide an easy way to breath in the HIM gas as a medicine.
[Eg: run a ball mill with black sand for 3 hours as per Joe's instructions, then open it and breathe in the air from inside the container. After which, you'd get a nice dose of the famous HIM gas but without previously passing through the exhaust port of a vacuum pump, nor having to use corrosive chemicals.]

At least it all seems clear in my head, but hoping that it still makes sense after putting it down on the page.
[EDIT: this model also explains why the 3 chemistry pre-treatment processes mentioned by Joe would increase PM yield. In those cases, the pre-treatments are simply stripping off the outside layers of each grain of magnetite exposing the HIM particles hiding inside. And of course, those methods would also require immediate fire assay after processing.]
 
Last edited:

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
I think the high energy collision of the balls creates exotic effects when they slam together it can burn a hole trough paper and release a small flash of light.
you're absolutely right that there's the potential for those conditions to engender some exotic reaction/s.
I was thinking about what you said, and I reckon that's exactly what's happening with the 'mercury in ball mill' technique.
I never mentioned it in the OP, because IMO mercury should be avoided at all costs...BUT....
there is another way of extracting gold from black sands by putting black sand with metallic mercury together in a ball mill for a few hours.
Then distill the mercury in a retort to extract the newly released gold.
This process is a thing for gold miners and has been so for quite some time, see this video for a demo:
[BTW, I think it's hilarious that he wears a proper breathing mask when dissolving lye but nothing when handling mercury..LOL]

Anyway, just as @Lakshmana said, IMO the exotic effects from steel balls colliding are causing mercury to become gold.
Of course, this "impossible" reaction can only occur because of the presence of HIM which is liberated from the black sand grains getting broken into smaller pieces [as was described in previous post].
 
Last edited:

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
Wanted to update the thread with a review of the video shown in the OP.
Here it is again, to save you scrolling back up to see which one I'm talking about:

I love that video for multiple reasons:
- It shows actual recovery of 5% precious metals from black sand(BS) (Eg: proof that Joe's 0.5 - 10% expectation is possible).
- The gold value alone from 300g of BS is AUD $2000, and only required a couple of dollars to extract it.
- The process shown is an amalgamation of all 3 techniques discussed in the OP
> grinding in a ball mill as per Champion's process
> mix black sand with powdered glass (aka silica) as per Milewski's process
> melt with lye, and then turn back to metallic gold by adding sulfur and iron as per Essene's process.
L> [The fire assay didn't actually add sulfur, but the BS already contained sulfides, meaning sulfur present in the reaction.]

I have thought for a long time, that the mining industry could have blown open the secret of alchemy many years ago if they simply asked the question: "what the fuck is going on?", because IMO that single video basically shows everything for unravelling the entire thing.
And the beautiful thing is that there is none of the standard disbelief and eye-rolling which we normally get when showing or discussing HIM based miracles.
The guy in the video said that the entire sample of BS had been previously run over a shaker table with NO GOLD VISIBLE.
He then runs a fire assay, and pulls out 5% of the sample as precious metal.
And yet there is not a single voice in the comments calling fakery or serving up the standard vitriol, doubt or derision.
The muggles just accept it all, thinking to themselves that there's nothing to see here.
[Compare that to the snarky comments on THIS video, which also operated on black sand and ironically produced far less gold.]
 
Last edited:

Mahavira

Terrae
Hermetic Pilgrim
Joined
Apr 4, 2024
Messages
295
Excellent research once again GA, thanks!

And in addition to the black sand's pre-treatment, it seems possible to maximize the precious metal yield even further with the x-ray irradiation method at the end of each heat-cool/freeze-grind cycles.
 

Dendritic Xylem

Invenies
Honorable Meister
Hermetic Pilgrim
Joined
Mar 1, 2010
Messages
621
GA, I could be wrong...but I think you might be jumping the gun on this one.
That assay video shows nothing out of the ordinary. They were processing shaker table concentrates from a rich ore. Not just any old black sand/magnetite. So the yield is not abnormal and not comparable to the black sand Joe was using.

Side note---the guy in that video is the son from the famous popandson sluice design.

I actually have Joe's rare/expensive book. I've run magnetite and non-magnetic black sands (from a historic gold bearing region) in a ball mill with multi-sized steel balls, with and without mercury for 6+ hours and got nothing out of the ordinary. So I think the situation is more complicated than you think. Prospectors/miners/companies/scientists have been ball milling black sands with mercury forever. If synthesizing commercial amounts of gold was that easy, the process wouldn't have flown under the radar.

Maybe some black sands work, but the ones I tried didn't. Also, pretty sure Joe's alleged best results with the ball mill method used dead commercial chemical mixes rather than Him-containing ores. I would look but I'm in the middle of a move and most of my books are in storage.
 

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
I think you might be jumping the gun on this one.
That assay video shows nothing out of the ordinary. They were processing shaker table concentrates from a rich ore. Not just any old black sand/magnetite.
Ahhh....I did not catch that subtlety. Thanks for pointing it out.

I've run magnetite and non-magnetic black sands (from a historic gold bearing region) in a ball mill with multi-sized steel balls, with and without mercury for 6+ hours and got nothing out of the ordinary. So I think the situation is more complicated than you think.
If you've got experience like that, then I'll take it on board.
Which regions did you collect the black sands from when you tried this?
Were they all sourced from the same basic region? Or from totally different regions? And roughly whereabouts?
Did any come from areas which experience regular freezing?
Only asking this, because if they all came from hot areas, then there'll be no surprise for me that they didn't yield anything.

Prospectors/miners/companies/scientists have been ball milling black sands with mercury forever. If synthesizing commercial amounts of gold was that easy, the process wouldn't have flown under the radar.
Yeah, you're probably right there.
Thanks for bringing me back down to Earth.

pretty sure Joe's alleged best results with the ball mill method used dead commercial chemical mixes rather than Him-containing ores.
Yes, that's right.
But IMO Joe's chemical mixtures always had at least one HIM containing substance (IMO it was usually calcium oxide and/or silica and then later black sand).
If you believe the account presented in the book "The platinum Canon shipwreck", then Joe's yields became considerably higher after switching in the mysterious alchemy inducing limestone compound.
 
Last edited:

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
what I'm particularly interested in WRT this, is that this might also provide an easy way to breath in the HIM gas as a medicine.
[Eg: run a ball mill with black sand for 3 hours as per Joe's instructions, then open it and breathe in the air from inside the container. After which, you'd get a nice dose of the famous HIM gas but without previously passing through the exhaust port of a vacuum pump, nor having to use corrosive chemicals.]
Just came across an interesting little tidbit from THIS page:
a research colleague reported to me in late 2007 that he had been in contact with a medical doctor in Sweden who claims to have discovered that miners working in a rural Swedish mine -- a mine exhibiting modestly high levels of ionizing radiation and bearing deposits of both pitchblende ore (uranium ore) and magnetite -- were actually growing younger and being healed of chronic disease due to their time spent in the mine tunnels.
Even though the author believed that the cause of healing was radiation from uranium, for me it's proof of what I said.
That that breaking up magnetite and breathing in air exposed to it, is indeed medicinal.
 

Dendritic Xylem

Invenies
Honorable Meister
Hermetic Pilgrim
Joined
Mar 1, 2010
Messages
621
Which regions did you collect the black sands from when you tried this?
Various spots around the South Mountains gold belt in NC. Also some eBay magnetite from Nevada and Arizona.
NC area definitely freezes.

That that breaking up magnetite and breathing in air exposed to it, is indeed medicinal.
It can also kill you. Magnetite sometimes comes contaminated with arsenic. Be careful.

Kevin's book says that the magnetite radiates SM which is why he recommends crystallizing salts with powdered magnetite mixed in, even though the salts don't actually break down the magnetite. So maybe Him/SM exists in various forms on a spectrum, where one side of the spectrum has more corporealized forms, while the other side of the spectrum has more subtle/spiritual forms. The Him "particles" trapped in the crystal lattice would be a more corporeal form...while the type that radiates outward (like Odic energy) is a more subtle form. Just speculating.

It does seem that alchemy is about removing this passenger from its crude clothing, purifying/concentrating it, and giving it the conditions to evolve into something better. Then you can enjoy the health benefits of the universal spirit without the potentially poisonous influence of its naturally dirty host.
 

Appleheads

Terrae
Hermetic Pilgrim
Joined
Jan 5, 2024
Messages
231
I had a nice spot to harvest Black sand in my locality, people didn't follow the rules, and is closed now. I fortunately I had a harvest lead/silver Galena, with a touch of gold before it was closed. Some of the most fascinating mineral specimens I ever found.

Apparently though, Black Sand, is everywhere at the bottom of the brook, stream, river, etc.
 

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
Did any come from areas which experience regular freezing?
Various spots around the South Mountains gold belt in NC. Also some eBay magnetite from Nevada and Arizona.
NC area definitely freezes.
I've run magnetite and non-magnetic black sands (from a historic gold bearing region) in a ball mill with multi-sized steel balls, with and without mercury for 6+ hours and got nothing out of the ordinary. So I think the situation is more complicated than you think.
Thank you very much for your contribution '@Dendritic Xylem' because it proves that the secret sauce IS NOT black sands which have been charged by nature from periodic freeze and thaw as I previously thought (although I do think this would still increase the 'charge' on the HIM portion inside the black sands though).

So...in a vain effort to find out for sure, I did a smelt on the weekend.
I ball milled black sand (which had been previously subjected to bion pack process) for a day, then used the same receipe and proportions listed in the video (BS:lye:borax:silica:bismuth -> 4:4:4:2:1).
The major difference was that I substituted the lead with bismuth, but when finished the smelt I didn't bother completing with the cupel process because I also saw nothing out of the ordinary (Eg: the recovered bismuth doesn't look like more than I started with).
The smelt used an electric furnace with graphite crucible and held the temperature for 2 hours.

IMO the only remaining possibility to explain things is that the presence of sulfur is indeed the secret sauce causing the difference between success and failure WRT extracting precious metals from black sand.
Perhaps it is simply that the only black sands which produce precious metals are the ones that also contain sulfides.

The geode process requires sulfur, as did the solomon process, the JC gunpowder burn process, and also the ormus to metal furnace process.
IMO the presence of sulfur in all these receipes is probably not a coincidence.

So, I'll have to do one more test to finally write this off, by redoing the smelt adding either sulfur or a sulfide.
But I'm quite fearful of putting sulfur into a slurry containing charged HIM and running high heat.
IMO this should only be done on a new moon and using gas heat to reduce the chances of generating DOR (which IMO is actually strong neutron radiation).

The next new moon, isn't for another 12 days, and I don't even have a gas furnace which can get to 1000 celcius, so I'll have to try to ghetto something in the meantime.
Then I'll report the result back to the forum.

Kevin's book says that the magnetite radiates SM which is why he recommends crystallizing salts with powdered magnetite mixed in, even though the salts don't actually break down the magnetite. So maybe Him/SM exists in various forms on a spectrum, where one side of the spectrum has more corporealized forms, while the other side of the spectrum has more subtle/spiritual forms. The Him "particles" trapped in the crystal lattice would be a more corporeal form...while the type that radiates outward (like Odic energy) is a more subtle form. Just speculating.
I agree, but IMO it's putting 'charge' on the HIM is what causes it to move along the spectrum becoming more corporealised.

It does seem that alchemy is about removing this passenger from its crude clothing, purifying/concentrating it, and giving it the conditions to evolve into something better. Then you can enjoy the health benefits of the universal spirit without the potentially poisonous influence of its naturally dirty host.
I always love to see truth written in a simple and easily understandable form.
 

Dendritic Xylem

Invenies
Honorable Meister
Hermetic Pilgrim
Joined
Mar 1, 2010
Messages
621
I didn't bother completing with the cupel process because I also saw nothing out of the ordinary (Eg: the recovered bismuth doesn't look like more than I started with)
Make sure to ball mill the slag just in case some bismuth was lost in it. You can separate it with a gold pan.
I think you should still cupel it just to be sure

But I'm quite fearful of putting sulfur into a slurry containing charged HIM and running high heat.
Even without HIM you need to be careful firing sulfur/sulfides at high heat. It can produce dangerous gases like H2S/SO2. So make sure you do it outside, on a windy day, somewhere far from neighbors. And wear a good cartridge style mask.

Just some advice. Don't for one second put too much faith/belief in any of these transmutation processes until you personally have a successful replication with gold in hand. It's fine to entertain the concepts and experiment with the processes....but don't spend too much time developing theories built on evidence you haven't personally verified yet. I wasted too many years doing just that.


But here's more info for the thread to thicken the plot
(edit--I haven't successfully replicated these processes, so don't put too much faith in them)

This patent says that mercury releases SO2 when transmuting to gold...

These deal with converting iron into gold. No sulfur required...
 

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
Before working with ORMUS-containing sources containing large amounts of ORMUS particles, such as azomite, natural Dead Sea salt, sea salt, iron ore magnetite, rock oil mineral, Himalayan pink/black salt, gold or silver ore,
it is useful to activate them by exposing them to a pulsating magnetic field, cyclically calcining them at 250-300 degrees Celsius, then boiling them in water and
freezing them. Then, grind them for a long time in a ball mill.
My method extracts only the active portion of ORMUS from the solution, leaving a significant portion in the solid salts or solution
@Vladimirv how did you turn your magnetite into a solution?

There's only a couple of options I'm aware of and they're all problematic:
> burn in dry lye and dissolve in water [dangerous]
> boil in lye solution [slow]
> soak in CLR [expensive]
> soak in aqua regia [expensive]

Is there something I missed?

UPDATE: I missed "soak in HCl acid and peroxide"
Google AI says:
Yes, magnetite will dissolve in a mixture of hydrochloric acid and hydrogen peroxide. The hydrochloric acid acts as the primary solvent, while the peroxide acts as an oxidizing agent that can assist in the dissolution process.
How It Works:
Acid Dissolution:
Magnetite dissolves in strong acids like HCl to form ferrous and ferric chlorides.
Peroxide Action: The addition of hydrogen peroxide helps oxidize any Fe2+ to Fe3+ and can speed up the reaction.
Conditions: While it can dissolve in HCl alone, the combination is often used to ensure complete dissolution, particularly in cleaning or etching processes, or to break down nanoparticles. The reaction is generally faster with heating, but the combination of a strong acid like HCl with a strong oxidizer like H2O2 is effective at breaking down the iron oxide structure.
So if it's true, then that'll be the one to use.

The next new moon, isn't for another 12 days, and I don't even have a gas furnace which can get to 1000 celcius, so I'll have to try to ghetto something in the meantime.
Then I'll report the result back to the forum.
Just updating that I did indeed successfully ghetto a high temp gas furnace, also purchased a large graphite crucible, and even ghetto'd some furnace tongs.
But I haven't been able to do any smelting due to high bushfire risk, so I've had to put the project on hold until temperatures and conditions fully calm down.
 
Last edited:

Vladimirv

Terrae
Hermetic Pilgrim
Joined
Dec 7, 2025
Messages
152
I saw a video on YouTube where someone used a rubber ball mill with quartz glass balls
Link

Everything changed when Khanchuk's group tested graphite deposits not using the traditional chemical "test tube" method, but using ion mass spectrometry and neutron activation analysis. The ion mass spectrometer, in particular, helped reveal nanoforms of gold and platinum group metals "hidden" in the graphite. These were undetectable by traditional chemical analysis, as gold did not separate from the graphite "sandwich."
What did this lead to? A complete change in understanding of the concentration of precious metals in graphite deposits. Khanchuk's group analyzed rock samples from long-known graphite deposits in Primorye, Khabarovsk Krai, and the Jewish Autonomous Oblast. Moreover, the deposit in Primorye has been known since the 1950s, and it can be mined using open-pit mining, meaning it can be developed without expensive mining operations.

Conventional chemical analysis of the samples analyzed by the group of scientists yielded a gold concentration of 3.7 grams per ton, while spectrographic analysis yielded a gold concentration of up to 17.8 g/t. Platinum: 0.04–3.56 g/t in vitro and up to 18.55 g/t spectrometer analysis. Palladium, a valuable catalyst and additive that improves the properties of metal alloys, was detected at concentrations of up to 18.55 g/t, compared to 0.02–0.55 g/t using traditional analysis. This means that the precious metals were found to be present in much greater quantities than previously thought.
 

Vladimirv

Terrae
Hermetic Pilgrim
Joined
Dec 7, 2025
Messages
152
1770807185773.png

I am 100% sure that this graphite contains a lot of ORMUS particles.
Link


These guys seem to know why this graphite is actually diamagnetic and what its value is, and they sell it at such prices.
 

Lakshmana

Lapidem
Patron of the Arts
Hermetic Pilgrim
Joined
Jan 24, 2022
Messages
1,081
I have used synthetic graphite powder for experiments before its very slippery and shiny, they make it by heating coal minerals in a sealed container to very high temperatures, the naturally occurring rocks are very rare.

The slipperiness of graphite supposedly comes from the hexagonal crystalline geometry graphite = graphene with many layers.

For some reason i was able to make the Graphite powder attracted to magnets, "Diamagnetic" :)
 

theFool

Hermes Trismegistus
Patron of the Arts
Honorable Meister
Hermetic Pilgrim
Joined
Jan 8, 2009
Messages
1,362
View attachment 4223

I am 100% sure that this graphite contains a lot of ORMUS particles.
This is a very good intuition of yours. When heated at red hot heat the graphite becomes magnetic (attracts to magnet). This cannot be attributed to iron but probably to ormes that were trapped in graphite and were reduced by heat and carbon into a magnetic form.

Some of my ideas on the phenomenon:
 

Lakshmana

Lapidem
Patron of the Arts
Hermetic Pilgrim
Joined
Jan 24, 2022
Messages
1,081
Maybe it's due to oxidation/contact with atmosphere if it's properly protected from air it seems to not go ferromagnetic.
 

Andro

Alchemical Adept
Magus de Moderatio
Patron of the Arts
Honorable Meister
Hermetic Pilgrim
Joined
Dec 10, 2009
Messages
8,263
Maybe it's due to oxidation/contact with atmosphere if it's properly protected from air it seems to not go ferromagnetic.
Ripley writes in Liber Secretisimus:

"Take out the black faeces which remain in the bottom of our Vessel, called our Dragon, and grind it into small powder, and calcine it in two crucibles luted together."
 

theFool

Hermes Trismegistus
Patron of the Arts
Honorable Meister
Hermetic Pilgrim
Joined
Jan 8, 2009
Messages
1,362
Maybe it's due to oxidation/contact with atmosphere if it's properly protected from air it seems to not go ferromagnetic.
Or maybe it escapes as carbonyl; as iron or nickel do when reacting with carbon monxide.
 

Dendritic Xylem

Invenies
Honorable Meister
Hermetic Pilgrim
Joined
Mar 1, 2010
Messages
621
I googled "heated graphite paramagnetic" and got this...

  • Magnetism in Graphite Derivatives (Graphite Oxide): While pure, heated graphite remains diamagnetic, graphite oxide (a derivative) shows complex magnetic behaviors, including ferromagnetic and antiferromagnetic tendencies. When graphite oxide is heated, this mixed behavior can transition, and in some reduced forms, it may display paramagnetic or altered magnetic properties due to the removal of oxygen-containing functional groups.

Explains this...
Maybe it's due to oxidation/contact with atmosphere if it's properly protected from air it seems to not go ferromagnetic.
 

mishava

Visita
Hermetic Pilgrim
Joined
May 24, 2026
Messages
66
what is special about black sand? Why can't you use regular brown beach sand or dirt, etc?
 

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
Why can't you use regular brown beach sand or dirt, etc?
You can.
Some (or all) of those might also yield gold in varying amounts, it just won't be as much as you'll get from magnetite black sand.

what is special about black sand?
That is the million dollar question. IMO it's simply because magnetite has the highest levels of HIM of any naturally occuring mineral.
Does it really matter though?
If you want gold (and you clearly do), then use magnetite black sand and you're good.
[Just make sure to add some kind of sulfur though to make use of the popcorn effect, I would use copper sulphate myself].
 
Last edited:

ghetto alchemist

Hermes Trismegistus
Honorable Meister
Hermetic Pilgrim
Joined
Mar 21, 2011
Messages
1,537
(BS:lye:borax:silica:bismuth -> 4:4:4:2:1)
L> + copper sulfate ~0.5
Figured that I should probably update the thread with what I currently know.
I did end up ghetto'ing a high temperature gas furnace which easily gets up to 1000+ degrees celcius.
It also holds a large graphite crucible.
So I ended up running a smelt with the above ratios based on 300 grams of magnetite black sand, according to what was shown in the video [it may or may not have made a difference, but for what it's worth I ran the smelt during the daytime of a new moon].
[I also added copper sulfate, expecting it to decompose into SO2 from the molten lye, according to popcorn theory]
[It's also expected that the same lye will partially dissolve the outside layer of magnetite exposing the HIM center to SO2 (also according to popcorn theory)].


The result was a very heavy button of bismuth.
I've handled a lot of gold and gold alloy in my life, anyone who has done the same will know what I'm talking about when I say that gold alloy has a definate heft to it that distinctly tells you it's gold.
When I held the bismuth button it had the exact same feeling as a gold alloy.
I estimated the button had about 30-40 grams of excess metal, and from that I think it was probably 30 grams of gold.
That is at the upper end of Joe Champion's predicted band of yield/s, so not outside the realms of possibility.

Unfortunately I met with a couple of problems trying to separate the gold from the bismuth.
IMO my failure was a combination of my being inexperienced at these things and also from my sub-standard equipment.
So I finally gave up the idea and decided to try another smelt with copper instead of bismuth (which I haven't done yet).
But to be clear, there is no doubt in my mind that this black sand smelting process (and receipe) yields gold, the only unknown thing is exactly how much it produces.
Of course, I also need to determine the easiest way to get the gold out.
 
Last edited: